| Dimensions and weights | |
|---|---|
| Length approx. | 3605 mm |
| Width/depth approx. | 1739 mm |
| Height approx. | 1905 mm |
| Weight approx. | 2800 kg |
Roll over image to zoom in
TREIPINK OPTIturn TX 6222V
37,500.00€ + KM
Kirjeldus
Tehnilised andmed
Lisad
Kirjeldus
- Heavily ribbed cast iron machine bed
- One-piece steel machine base
- High headstock housing rigidity due to heavily ribbed 25GG cast iron
- Precisely machined slide
- Shafts on needle bearings, all components lubricated in oil bath
- Bed guides hardened and precision ground
- Accessible to all electronic controls centrally
- All gearwheels
- All electronic controls are centrally accessible
- All gears of the feed gear are made of steel, hardened and precision ground
- Manual gears decoupled and tested according to EN 23125
- Two-channel right/left switch tested according to EN 23125
- Switch with life cycle calculation, tested according tof according to EN ISO 13849
- Coolant system with separate 50 litre coolant tank with level indicator and oil separator; easy and complete draining and cleaning according to DIN
- Complete lead and drawbar cover
- Complete illumination of the work area
- Hardened and ground face spindle ensures tremendous accuracy and durability
- High chip removal during roughing is no problem due to the large chip removal capacity
- Lockable chip guard moves with the bed slide with integrated position indicator and coolant hose, manually movable
- No change gears necessary
- .With safety device against simultaneous operation of tapping and feed mechanism
- Electronically braked motor
- Electronic feed cut-off of Z-axis
- Electronic position cut-off with quadruple position stop
- Three-jaw lathe chuck included as standard
- Quick-change steel holder SWH 7-C
- Steel holder 32 x 130 type D forr square chisel 25 mm
- Digital position indicator DP700
Tehnilised andmed
| Cooling lubricant system | |
|---|---|
| Coolant pump output | 0,1 kW |
| Electrical connections | |
|---|---|
| Total rated value | 12 kW |
| Electrical Data | |
|---|---|
| Supply voltage | 400 V |
| Mains frequency | 50 Hz |
| Feed | |
|---|---|
| Longitudinal feed range | 0,05 – 1,5 mm/rev |
| Number of longitudinal feeds | 55 |
| Flat feed range | 0,025 – 0,75 mm/rev |
| Number of flat feeds | 55 |
| Feed motor drive power | |
|---|---|
| Drive power | 0.55 kW |
| Pitches | |
|---|---|
| Metric pitch | 0,5 – 15 mm/rev |
| Number of metric pitches | 55 |
| Imperial pitch | 60 – 2 Gg/1″ |
| Number of imperial pitches | 55 |
| Diametrical pitch | 120 – 4 Gg/π |
| Number of diametrical pitches | 55 |
| Modular thread pitch | 0,25 – 7,5 mm x π |
| Number of modular thread pitches | 55 |
| Leading spindle | 6 mm |
| Speed range | |
|---|---|
| Number of gears | 2 x 3 Steps |
| Speed range | 14 – 1800 min¯¹ |
| Spindle | |
|---|---|
| Spindle chuck | Camlock DIN ISO 702-2 No. 8 |
| Spindle bore/rod passage diameter | 105 mm |
| Spindle cone | MT 7 |
| Tool holder | SWH 7-C |
| Tailstock | |
|---|---|
| Chuck | MK 5 |
| Quill stroke | 180 mm |
| Quill diameter | 72 mm |
| Travel | |
|---|---|
| Travel upper slide | 170 mm |
| Travel cross slide | 350 mm |
| Travel carriage saddle | 2000 mm |
| Work areas | |
|---|---|
| Max. height | 310 mm |
| Max. width | 2225 mm |
| Swing diameter above machine bed | 620 mm |
| Swing diameter in bed bridge | 880 mm |
| Swing diameter above longitudinal slide | 580 mm |
| Swing diameter above planing slide | 424 mm |
| Turning length in bed bridge | 231 mm |
Lisad
